

Rod seal, single-acting Type SD 01
The single-acting rod seal type SD 01 is primarily used in cylinders with one-sided pressurization. The media used in these applications range from mineral oil-based hydraulic liquids, environment-friendly bio-oils and water to flame-resistant hydraulic liquids and air. It promises stick-slip free running as well as good dry-running properties.
While the PTFE profile ring seals dynamically against the cylinder surface, the elastic O-ring ensures uniform contact pressure of the PTFE profile ring onto the cylinder surface, and at the same time, a static sealing between profile ring and groove base.
Even with low pressures, the piston seal shows a good sealing effect thanks to the inherent preload of the PTFE profile ring and the contact force of the preloaded O-ring. At higher system pressures, the medium pressurizes the O-ring causing it to press the PTFE seal with enhanced force against the cylinder surface.
With different material combinations, the piston seal can be used reliably across the whole pressure, speed and temperature range.
Application media
- Mineral oil-based hydraulic liquids
- Water
- Air
- Environment-friendly bio-oils
- Flame-resistant hydraulic liquids
- Other media, depending on the O-ring material
Application range
Pressure: up to 40 Mpa (400 bar)
Speed: approx. up to 15 m/s
Temperature: – 30 °C to + +200 °C (depending on the O-ring material)
Surface finish
Roughness depth | Ra | Rt |
Running surface | ≤ 0,3 µm | ≤ 3,0 µm |
Groove base | ≤ 1,6 µm | ≤ 16,0 µm |
Groove flank | ≤ 1,6 µm | ≤ 16,0 µm |
Installation dimensions
Rods ø D | Gap size S | ||||||||
---|---|---|---|---|---|---|---|---|---|
Heavy Design | Standard Design | Light Design | Groove base ø D | Groove width L +0,2 | Radius R | 10 Mpa max. | 20 Mpa max. | 30 Mpa max. | O-Ring line ø |
– | – | 8,0 – 18,9 | ø d + 4,9 | 2,2 | 0,4 | 0,3 | 0,2 | 0,15 | 1,78 |
– | 8,0 – 18,9 | 19,0 – 37,9 | ø d + 7,3 | 3,2 | 0,6 | 0,4 | 0,25 | 0,15 | 2,62 |
8,0 – 18,9 | 19,0 – 37,9 | 38,0 – 199,9 | ø d + 10,7 | 4,2 | 1,0 | 0,4 | 0,25 | 0,2 | 3,53 |
19,0 – 37,9 | 38,0 – 199,9 | 200,0 – 255,9 | ø d + 15,1 | 6,3 | 1,3 | 0,5 | 0,3 | 0,2 | 5,33 |
38,0 – 199,9 | 200,0 – 255,9 | 256,0 – 649,9 | ø d + 20,5 | 8,1 | 1,8 | 0,6 | 0,35 | 0,25 | 7,0 |
200,0 – 255,9 | 256,0 – 649,9 | 650,0 – 900,0 | ø d + 24,0 | 8,1 | 1,8 | 0,6 | 0,35 | 0,25 | 7,0 |
256,0 – 649,9 | 650,0 – 900,0 | – | ø d + 27,3 | 9,5 | 2,5 | 0,7 | 0,5 | 0,3 | 8,4 |
PTFE profile ring material
PTFE + bronze
The standard for hydraulic applications, good gliding behavior, particularly pressure and abrasion resistant, cannot be used in aqueous solutions or acids
PTFE + Glass-MoS2
Particularly good resistance to wear and abrasion, application is possible even with poor lubricating pressure fluids, in water and in water-oil emulsions
PTFE + carbon
Exceptional resistance to abrasion and extrusion; can be used in water-hydraulics
For other possible materials see our overview of PTFE materials in the technical information section.
O-ring material
Nitrile rubber NBR
Temperature range − 30 °C to + 120 °C
Fluororubber FPM
Temperature range − 25 °C to + 200 °C
Overview of materials for dynamic seals
The following overview is a selection of typical PTFE materials used for seals, guide elements and wipers. Further PTFE materials are available for special applications.
Product data sheet (PDF)
Our data sheet for the Rod seal, single-acting Type SD 01 can be found here.
Get your product quickly!
To help you quickly and easily find the best solution for your products, please send us your product inquiry via the form below. So you can send us your specifications and requirements directly.
Product request rod seal, single-acting type sd 01
Discover our product competence.
With our products navigator you can get to the product you are looking for quickly.